
A breaker that won't reset, trips with nothing running, or feels hot needs a licensed electrician to find out why. Sometimes the breaker itself has failed; often the breaker is doing its job and the problem is on the circuit. Eggers Electric diagnoses and replaces breakers in Loveland, Fort Collins and Northern Colorado, with a written price before any work.
“…they are remarkably responsive to questions and needs during a project.”
Don't keep resetting a breaker that trips over and over, and never tape or hold a breaker on. Never remove the panel cover.
The handle won't stay on, or trips the moment you flip it. That points to a short, a ground fault or a failed breaker.
A space heater, microwave or vacuum on a shared circuit can overload it. The fix may be a dedicated circuit, not a bigger breaker. See appliance circuits.
Can mean a failing breaker, a loose connection, damaged wiring or moisture in an outdoor box.
A breaker should never be hot to the touch or buzz. It can mean a loose connection at the breaker or the bus. Call us right away.
These detect specific faults. Nuisance tripping can come from a shared neutral, damaged wiring or certain appliances. See AFCI breakers.
A breaker that wiggles in its slot may not be making good contact, and the panel bus can be damaged. Sometimes the fix is a breaker; sometimes it's the panel.
Two wires under a terminal made for one, often flagged on a home inspection. We give each wire its own breaker or make a proper connection.
Some older panels use breakers that are hard to find. We tell you whether correct replacements are available or whether the panel should go.
| Fix the circuit | Replace the breaker | Upgrade the panel | |
|---|---|---|---|
| When | Breaker is fine; the problem is wiring, a device or an overload | Breaker failed, is damaged or the wrong type | Panel is damaged, full, unsafe or has no correct replacement breakers |
| What we do | Find and repair the fault, or add a circuit | Install the correct listed breaker for your panel | Replace the panel; often adds surge protection |
| Permit | Depends on the work | Depends on the work and your city | Yes |
| See | Troubleshooting & repair | This page | Panel upgrades |
A breaker has to match the panel it goes in and the wire it protects.
On every visit, a licensed Eggers electrician handles the job you called about and runs our full Safety Inspection. There's a $89 service charge — and it is credited toward your job if you move forward.
The 8 points: electrical panel, main grounding & bonding, GFCI protection, smoke & CO detectors, outlets & switches, visible wiring, exterior electrical, and whole-home surge protection. Each one is marked Pass or Needs Attention.
You get a written price before any work starts.
“I called them early this morning, and within a couple of hours Chris was here to figure out why one circuit kept kicking the breaker. Turns out it was a floor outlet that had been cooking for a while. We had no clue.…”
“I called them early this morning, and within a couple of hours Chris was here to figure out why one circuit kept kicking the breaker. Turns out it was a floor outlet that had been cooking for a while…”Google review

Questions? Call 970-669-1883 or email info@eggerselectric.com.
Serving Loveland, Fort Collins and Northern Colorado · 970-669-1883
Written by the Eggers Electric team
Usually an overloaded circuit, a short, a ground fault or a failing breaker. If it trips again right after you reset it, leave it off and call us.
Yes. Breakers wear out, and heat, loose connections and repeated trips can damage them. A breaker that won't reset, trips with nothing on, or feels hot may have failed.
We don't recommend it. The panel stays live even with the main off, and the breaker has to be the correct listed type for your panel. Colorado lets homeowners do some work on the home they live in, with a permit, but panel work is not a do-it-yourself job.
No. The breaker protects the wire. A bigger breaker on the same wire can let it overheat. The fix is a new circuit or new wire.
They're likely on the same circuit and together draw more than it's rated for. Moving one, or adding a dedicated circuit, fixes it.
Replacing a single breaker typically takes about 30 minutes to 2 hours, depending on the breaker type and the panel's age and condition. Finding the cause of the problem first can add time.
A breaker can feel slightly warm under heavy load, but it should never be hot, buzz or smell. If it does, turn it off if it's safe and call us.
Through Dec 17: donate food for the Larimer County Food Bank and we’ll waive the $89.
★★★★★ Google 4.9 · 400+ reviews
Need an electrician?
On every visit, a licensed Eggers electrician handles the job you called about and runs our full Safety Inspection. There's a $89 service charge — and it is credited toward your job if you move forward.
Through Dec 17: bring non-perishable food for the Larimer County Food Bank and we’ll waive the $89 service charge.
Schedule Serviceor call 970-669-1883 · Call 7 days, 7am–8pm
Ask a question
Send us a message and we’ll follow up. Need help now? Call 970-669-1883.