OVER 50 YEARS★ LOCALLY OWNED ★SINCE1973
Eggers Electric service vans parked at the Loveland shop

Circuit breaker repair & replacement in Loveland & Fort Collins

A breaker that won't reset, trips with nothing running, or feels hot needs a licensed electrician to find out why. Sometimes the breaker itself has failed; often the breaker is doing its job and the problem is on the circuit. Eggers Electric diagnoses and replaces breakers in Loveland, Fort Collins and Northern Colorado, with a written price before any work.

Call 970-669-1883
“…they are remarkably responsive to questions and needs during a project.”
Google review · Fort Collins · Feb 2026 EV & inspections
Call 7 days, 7am–8pm

Schedule service or ask a question

Call 7 days, 7am–8pm
Same-day service is often available.

Our promise

  • Upfront pricingYou approve the price before work starts.
  • On-time arrivalWe show up when we say we will.
  • Workmanship warranty1-year workmanship warranty on our work.
  • Licensed electriciansBonded, insured and local.

First: what you can safely check

  1. Unplug things on the circuit, then try resetting once: push the handle fully to OFF, then back to ON.
  2. Check for a tripped GFCI outlet in a nearby bath, kitchen, garage or outside. It can cut power to other outlets.
  3. Stop if it trips again right away, feels hot, buzzes or smells like burning. Leave it off and call us.

Don't keep resetting a breaker that trips over and over, and never tape or hold a breaker on. Never remove the panel cover.

Breaker problems we fix

Breaker won't reset

The handle won't stay on, or trips the moment you flip it. That points to a short, a ground fault or a failed breaker.

Trips when one appliance runs

A space heater, microwave or vacuum on a shared circuit can overload it. The fix may be a dedicated circuit, not a bigger breaker. See appliance circuits.

Trips with nothing running

Can mean a failing breaker, a loose connection, damaged wiring or moisture in an outdoor box.

Hot, buzzing or scorched breaker

A breaker should never be hot to the touch or buzz. It can mean a loose connection at the breaker or the bus. Call us right away.

AFCI or GFCI breakers that keep tripping

These detect specific faults. Nuisance tripping can come from a shared neutral, damaged wiring or certain appliances. See AFCI breakers.

Loose breaker or burned bus

A breaker that wiggles in its slot may not be making good contact, and the panel bus can be damaged. Sometimes the fix is a breaker; sometimes it's the panel.

Double-tapped breakers

Two wires under a terminal made for one, often flagged on a home inspection. We give each wire its own breaker or make a proper connection.

Breakers no longer made

Some older panels use breakers that are hard to find. We tell you whether correct replacements are available or whether the panel should go.

Repair the circuit, replace the breaker, or upgrade the panel?

Fix the circuitReplace the breakerUpgrade the panel
WhenBreaker is fine; the problem is wiring, a device or an overloadBreaker failed, is damaged or the wrong typePanel is damaged, full, unsafe or has no correct replacement breakers
What we doFind and repair the fault, or add a circuitInstall the correct listed breaker for your panelReplace the panel; often adds surge protection
PermitDepends on the workDepends on the work and your cityYes
SeeTroubleshooting & repairThis pagePanel upgrades

Why the right breaker matters

A breaker has to match the panel it goes in and the wire it protects.

  • Approved for your panel. We use breakers the panel's label and instructions allow. A breaker that "fits" isn't the same as one that's approved for that panel.
  • Sized for the wire. A bigger breaker on the same wire removes the protection. If a circuit needs more capacity, it needs new wire or a new circuit, not a bigger breaker.
  • The right type. Some circuits need AFCI or GFCI protection, especially when a circuit is extended or modified. We tell you if yours does.
  • No counterfeits. The CPSC has recalled counterfeit breakers in the past because they may not trip, so where a breaker comes from matters.

How breaker repair works

  1. Your visit and Safety InspectionA licensed electrician runs the 8-point safety check.
  2. DiagnosisWe test the breaker and the circuit to find the real cause.
  3. OptionsFix the circuit, replace the breaker, or upgrade the panel, each with a written price.
  4. RepairWe install the correct breaker or fix the circuit, and pull a permit if the work needs one.
  5. Test and walkthroughWe test the circuit with you and label the panel. The work is backed by our 1-year workmanship warranty.

What's included in every visit

On every visit, a licensed Eggers electrician handles the job you called about and runs our full Safety Inspection. There's a $89 service charge — and it is credited toward your job if you move forward.

The 8 points: electrical panel, main grounding & bonding, GFCI protection, smoke & CO detectors, outlets & switches, visible wiring, exterior electrical, and whole-home surge protection. Each one is marked Pass or Needs Attention.

What affects the cost

  • Whether the breaker, the circuit or the panel is the problem
  • The type of breaker (standard, AFCI, GFCI or dual-function)
  • Whether correct replacement breakers for your panel are still made
  • Damage to the bus or wiring found when we open the panel
  • Whether the work needs a permit

You get a written price before any work starts.

What our neighbors say

400+ Google reviews
“I called them early this morning, and within a couple of hours Chris was here to figure out why one circuit kept kicking the breaker. Turns out it was a floor outlet that had been cooking for a while. We had no clue.…”
Google reviewRepairs & troubleshooting
  • “I called them early this morning, and within a couple of hours Chris was here to figure out why one circuit kept kicking the breaker. Turns out it was a floor outlet that had been cooking for a while…”
    Google review
  • BBB Accredited Business, A+ rating
  • Eggers Electric Google reviews
  • 2024 Quality Business Awards winner
  • 2023 NoCo Style Readers’ Choice winner
  • Eggers Electric on Yelp
Eggers Electric crew in front of company vans in Northern Colorado

Locally owned in Loveland since 1973. Your neighbors, not a national chain.

About Eggers Electric

Circuit breaker questions

Questions? Call 970-669-1883 or email info@eggerselectric.com.

Why homeowners choose Eggers

  • Locally owned in Loveland since 1973
  • Licensed electricians
  • Permits pulled and inspections handled
  • Eggers Safety Inspection on every visit

Serving Loveland, Fort Collins and Northern Colorado · 970-669-1883

Why does my breaker keep tripping?

Usually an overloaded circuit, a short, a ground fault or a failing breaker. If it trips again right after you reset it, leave it off and call us.

Can a circuit breaker go bad?

Yes. Breakers wear out, and heat, loose connections and repeated trips can damage them. A breaker that won't reset, trips with nothing on, or feels hot may have failed.

Can I replace a breaker myself?

We don't recommend it. The panel stays live even with the main off, and the breaker has to be the correct listed type for your panel. Colorado lets homeowners do some work on the home they live in, with a permit, but panel work is not a do-it-yourself job.

Can I just put in a bigger breaker?

No. The breaker protects the wire. A bigger breaker on the same wire can let it overheat. The fix is a new circuit or new wire.

Why does my breaker trip when I run the microwave and toaster?

They're likely on the same circuit and together draw more than it's rated for. Moving one, or adding a dedicated circuit, fixes it.

How long does it take to replace a breaker?

Replacing a single breaker typically takes about 30 minutes to 2 hours, depending on the breaker type and the panel's age and condition. Finding the cause of the problem first can add time.

Should a breaker feel warm?

A breaker can feel slightly warm under heavy load, but it should never be hot, buzz or smell. If it does, turn it off if it's safe and call us.

Schedule service onlinePick a day and time that works for you.
Loading available times…
Prefer to talk? Call 970-669-1883, 7 days a week, 7am–8pm.
Call 970-669-1883
Eggers Safety Inspection + diagnose/estimate — $89 service charge, credited toward your job. Schedule Service ›

Through Dec 17: donate food for the Larimer County Food Bank and we’ll waive the $89.

Google 4.9 · 400+ reviews

Need an electrician?

On every visit, a licensed Eggers electrician handles the job you called about and runs our full Safety Inspection. There's a $89 service charge — and it is credited toward your job if you move forward.

Through Dec 17: bring non-perishable food for the Larimer County Food Bank and we’ll waive the $89 service charge.

Schedule Service

Have a question? Ask us

or call 970-669-1883 · Call 7 days, 7am–8pm

Ask a question

How can we help?

Send us a message and we’ll follow up. Need help now? Call 970-669-1883.