OVER 50 YEARS★ LOCALLY OWNED ★SINCE1973
Eggers Electric service vans parked at the Loveland shop

Hot tub wiring requirements, explained before you buy.

Most full-size hot tubs need a dedicated 240-volt circuit with GFCI protection and a maintenance disconnect within sight of the tub, at least 5 feet from the water unless there's a barrier. Some smaller "plug-and-play" tubs run on 120 volts; a listed packaged unit can plug into a GFCI-protected outlet with a cord no longer than 15 feet. Metal parts near the tub get bonded, and switches and lights have clearance rules too. The tub's manual sets the circuit size; the permit and inspection confirm the rest.

Call 970-669-1883
“…they are remarkably responsive to questions and needs during a project.”
Google review · Fort Collins · Feb 2026 EV & inspections
Call 7 days, 7am–8pm

Schedule service or ask a question

Call 7 days, 7am–8pm
Same-day service is often available.

120-volt plug-in vs 240-volt hardwired

120-volt plug-in tub240-volt hardwired tub
CircuitA dedicated, GFCI-protected outlet sized to the tubA dedicated 240-volt circuit sized to the tub's manual
ConnectionCord no longer than 15 feet, for a listed packaged unitWired through a GFCI-protected disconnect to the tub
HeatingOften can't heat and run jets at full power at the same timeHeats and runs jets together
Best forSmaller tubs, mild use, simpler installsMost full-size tubs and year-round Colorado use
PermitYes, for a new outlet circuitYes

What every hot tub install needs

Dedicated circuit

Sized from the tub's installation manual. Nothing else shares it.

GFCI protection

Ground-fault protection on the tub's supply, usually in the disconnect. A listed unit with built-in GFCI protection is the exception the code allows.

Maintenance disconnect

A readily accessible disconnect within sight of the tub, at least 5 feet from the inside wall of the tub unless a permanent barrier separates them. It lets you or a technician shut power off at the tub.

Bonding

Metal parts within 5 feet of the tub, such as railings, fixtures and equipment, are bonded so they stay at the same voltage. A listed packaged spa may have its bonding built in.

Switches, outlets and lights

Wall switches go at least 5 feet from the inside wall of the tub. Lights above or near the tub have height and protection rules.

Panel capacity

A 240-volt tub is a big load. A load calculation shows whether your panel can carry it.

How we handle a hot tub hookup

  1. Eggers Safety InspectionA licensed electrician runs our 8-point check and looks at your panel and the tub spot.
  2. Read the manualWe size the circuit, GFCI and disconnect from your tub's installation manual.
  3. Plan the routeWe plan the wire run to the deck or patio and the disconnect location before the tub arrives.
  4. Permit and wiringWe pull the permit, run the circuit, install the disconnect and bond the area.
  5. Test and walkthroughWe test the GFCI, power up the tub with you and meet the inspector. The work is backed by our 1-year workmanship warranty.

What's included in every visit

On every visit, a licensed Eggers electrician handles the job you called about and runs our full Safety Inspection. There's a $89 service charge — and it is credited toward your job if you move forward.

The 8 points: electrical panel, main grounding & bonding, GFCI protection, smoke & CO detectors, outlets & switches, visible wiring, exterior electrical, and whole-home surge protection. Each one is marked Pass or Needs Attention.

Eggers Electric crew in front of company vans in Northern Colorado

Locally owned in Loveland since 1973. Your neighbors, not a national chain.

About Eggers Electric

Hot tub wiring questions

Questions? Call 970-669-1883 or email info@eggerselectric.com.

Why homeowners choose Eggers

  • Locally owned in Loveland since 1973
  • Licensed electricians
  • Permits pulled and inspections handled
  • Eggers Safety Inspection on every visit

Serving Loveland, Fort Collins and Northern Colorado · 970-669-1883

Does a hot tub need a dedicated circuit?

Yes. Whether it's a 120-volt plug-in or a 240-volt hardwired tub, it gets its own circuit sized from the tub's manual.

How far does the hot tub disconnect have to be from the tub?

At least 5 feet from the inside wall of the tub, within sight of it and readily accessible, unless a permanent barrier separates them.

Does a hot tub need GFCI protection?

Yes. The tub's supply needs ground-fault protection, usually provided in the disconnect. A listed unit with built-in GFCI protection is the exception.

Can I plug a hot tub into an outdoor outlet?

Only a listed 120-volt packaged tub, into a GFCI-protected outlet on its own circuit, with a cord no longer than 15 feet. Never use an extension cord.

Do I need a permit to wire a hot tub?

Yes. Hot tub circuits need an electrical permit and inspection in the towns and counties we serve. We pull it.

Should I wire the hot tub before it's delivered?

Yes, ideally. Having the circuit and disconnect ready means the tub can be filled and powered the day it arrives.

Schedule service onlinePick a day and time that works for you.
Loading available times…
Prefer to talk? Call 970-669-1883, 7 days a week, 7am–8pm.
Call 970-669-1883
Eggers Safety Inspection + diagnose/estimate — $89 service charge, credited toward your job. Schedule Service ›

Through Dec 17: donate food for the Larimer County Food Bank and we’ll waive the $89.

Google 4.9 · 400+ reviews

Need an electrician?

On every visit, a licensed Eggers electrician handles the job you called about and runs our full Safety Inspection. There's a $89 service charge — and it is credited toward your job if you move forward.

Through Dec 17: bring non-perishable food for the Larimer County Food Bank and we’ll waive the $89 service charge.

Schedule Service

Have a question? Ask us

or call 970-669-1883 · Call 7 days, 7am–8pm

Ask a question

How can we help?

Send us a message and we’ll follow up. Need help now? Call 970-669-1883.